Plug and Abandonment Challenges
Thru-Tubing Downhole Cutting and Logging are Challenges we can help you with

 

 

Plug and Abandonment may be dumping cement into a hole in the ground, but there are significant challenges when it comes to logging in situ cement behind the casing and downhole cutting of tubulars.

 

Thru-Tubing logging has been called the unachievable  "holy grail" of rigless Plug and Abandonment (P&A) while downhole cutting and severance is expensive with significant challenges.

 

Oilfield Innovations can help with rig and rigless slickline and wireline new technology capable of severing multiple tubulars and logging thru-tubing.

 

 

Loading...
The Holy Grail of Rigless Plug and Abandonment P&A

 

Oilfield Innovations have patented a more than one way of logging through tubing during well plug and abandonment (P&A) using conventional logging tools and/or new ways of implementing convention acoustic and sonic logging signals and there is no need to pull the tubing. Use the below button to read more.

 

Cement Bond Logging without pulling the Tubing (i.e. Thru-Tubing Cement Bond Logging)
Conventional Cutting has LIMITS
Conventional Severing Methods can't cut clamps and control lines

 

The above various conventional options for downhole cutting can be used to cut or sever one (1) tubular but what about cutting clamps, control lines and any surrounding tubulars?  Fluid abrasive cutting can cut more than one tubular as shown below... but it is not a "thru-tubing" tool.  A "thru-tubing" cutter than can cut through tubing, clamps, control lines and casing simultaneously would be very valuable in plug and abandonment (P&A).

 

We have a New Way of Cutting

 

 

Oilfield Innovations has a new way of cutting tubulars downhole!  Our patented "thru-tubing" method can cut anywhere within a well bore using diamond wire deployed as a free filament similar to horticultural strimmers or "weed wackers,"  whereas conventional cutting of two or more tubulars is only possible near surface using abrasive jet cutting or above surface using a diamond wire saw.  Diamond wire technology is a proven cutting means that can be deployed downhole on a motor to cut through tubing, control lines, clamps, casing, cement and rock, whereas conventional cutters can only cut the tubing.

 

 

What of you could cut through multiple tubulars using a thru-tubing cutter

 

 

 

 

Disclaimers: Oilfield Innovations Limited (OILtd) does not promise that the site or any content, service or feature of the site or new technology will be error-free or that any defects will be corrected, or that your use of the site or technology will provide specific results. The site and its content are delivered on an “as-is” and “as-available” basis. All information provided on the site is subject to change without notice. OILtd cannot ensure that any files or other data you download from the site will be free of viruses or contamination or destructive features. OILtd disclaims all warranties, express or implied, including any warranties of accuracy, non-infringement, merchantability and fitness for a particular purpose. OILtd disclaims any and all liability for the acts, omissions and conduct of any third parties in connection with or related to your use of the site and/or any OILtd technologies or services. You assume total responsibility for your use of the site and any linked sites or new technologies. Your sole remedy against OILtd for dissatisfaction with the site or any content is to stop using the site or any such content or technology. This limitation of relief is a part of the bargain between the parties. The above disclaimer applies to any damages, liability or injuries caused by any failure of performance, error, omission, interruption, deletion, defect, delay in operation or transmission, computer virus, communication line failure, theft or destruction of or unauthorized access to, alteration of, or use, whether for breach of contract, tort, negligence or any other cause of action. OILtd reserves the right to do any of the following, at any time, without notice: (1) to modify, suspend or terminate operation of or access to the Site, or any portion of the Site, for any reason; (2) to modify or change the Site, or any portion of the Site, and any applicable policies or terms; and (3) to interrupt the operation of the Site, or any portion of the Site, as necessary to perform routine or non-routine maintenance, error correction, or other changes.

 

 

 

Plug and Abandonment Challenges
Thru-Tubing Downhole Cutting and Logging are Challenges we can help you with
The Holy Grail of Rigless Plug and Abandonment P&A
Cement Bond Logging without pulling the Tubing (i.e. Thru-Tubing Cement Bond Logging)
Conventional Cutting has LIMITS
Conventional Severing Methods can't cut clamps and control lines
We have a New Way of Cutting
What of you could cut through multiple tubulars using a thru-tubing cutter
Plug and Abandonment Challenges
Thru-Tubing Downhole Cutting and Logging are Challenges we can help you with
The Holy Grail of Rigless Plug and Abandonment P&A
Cement Bond Logging without pulling the Tubing (i.e. Thru-Tubing Cement Bond Logging)
Conventional Cutting has LIMITS
Conventional Severing Methods can't cut clamps and control lines
We have a New Way of Cutting
What of you could cut through multiple tubulars using a thru-tubing cutter